Power-Line (TDF)

• Direct Drive Twin Fan (Run & standby)
• Backward Curved Centrifugal Impellors
• Operating temperatures up to 40°C
• Performance range up to 2.72m3/s
• Static Pressure Development up to 500pa
• Speed Controllable
• Quality assured to BS EN ISO 9001
• Performance listed to BS 848 Part 1

The TDF range are twin backward curved centrifugal impellors (Run & Standby) designed for induct installations.

Casings
Robustly constructed from galvanised sheet steel, fitted with proprietry flanges at each end in accordance with DW142.

Impellers
Aerodynamically designed backward curved constructed from aluminium or steel plate depending on size and rotational speed.

The rotor of the external rotor motor forms the hub of the impeller. Rotors and impellers are factory matched and statically and dynamically balanced on precision machines according to VDI2060 quality class Q6.3.

Motors
Maintenance free external rotor motors with generously dimensioned sealed for life ball bearings encapsulating a high temperature lubricant. The bearings allow for the fan to be mounted at any angle.

Insulation is Class B with the enclosure IP44 according to DIN 40050. The electrical design corresponds to VDE 0530/12.84. The motors are suitable for operation in atmosphere up to 95% RH and ambients up to 40°C.

Motors are wound to suit either 240V 50HZ 1PH or 415V 50HZ 3PH electrical supply. All motors are fitted with Hot Spot protection by means of a thermal contact switch incorporated in the motor windings to prevent motor damage due to overloading. As the motors have a special torque-speed characteristic they are ideally suitable for speed control by voltage reduction.

Performance
Performance figures given have been tested using installation Type ‘D’ in accordance with BS848 Part 1 1980 and BS848 Part 2 1985. The aerodynamic performance data being to tolerance Class ‘C’ as recommended by BSI C.A.M.E Scheme, Certification No CM005.

Sound Levels
Sound Levels are measured in a reverberent chamber in accordance with BS848 Part 2. Sound level measurements are taken with the fan operating at 20% of its maxium pressure development.

Published dBA figures are sound pressure levels measured at a distance of 3m with spherical sound level propagation. It is included for comparative purposes only and the real sound level experienced will depend on the acoustic characteristics of the area being served.

Quality Assurance
Design and manufacture is in accordance with Quality Assured to BS EN ISO9001

DIMENSIONS:

Unit A B C D E F G H J K L N KG
TDF220 375 330 570 115 400 355 25 9 40 150 115 110 24
TDF250 375 330 570 115 400 355 25 9 40 150 115 110 26
TDF280 425 540 780 190 450 565 25 9 40 150 115 175 40
TDF320 500 655 900 230 525 680 25 9 50 150 130 220 65
TDF380 550 745 1015 260 585 780 35 11 50 160 130 240 75
TDF420 625 830 1130 295 600 865 35 11 50 230 230 220 103
TDF480 700 925 1250 325 735 960 35 11 65 230 230 300 112
TDF520 775 1055 1385 355 810 1090 35 11 50 230 230 350 145
TDF600 850 1200 1530 400 885 1235 35 11 55 230 230 400 180
TDF700 950 1280 1675 430 985 1295 35 11 55 230 230 450 203
Image of Trackmaster Twin Fan Controller (ITC)
Trackmaster Twin Fan Controller (ITC)

 

Please click here for the latest product alternative

The ITC model provides automatic changeover on fan failure as well as enabling a manual selection of either fan for duty sharing or test purposes. (BMS compatible via volt free contacts). This controller must have a permanent live supply. Any On/Off switching must be via the sensor connections S1 and SG terminals.

Stock Ref. No: 10314200
This Model no longer available
Image of Trackmaster Twin Fan Controller (ITC-DS)
Trackmaster Twin Fan Controller (ITC-DS)

The ITC-DS model (Duty sharing). Incorporates a timing mechanism which operates alternate fans on 12 or 24 hour intervals, thus ensuring the extended life of the fan bearings. The controller also provides automatic changeover on fan failure along with the facility for manual selection of either fan. (BMS compatible via volt free contacts). This controller must have a permanent live supply. Any On/Off switching must be via the sensor connections S1 and SG terminals

Stock Ref. No: 10314210
Price £600.11 (excl VAT)
Image of RSC - Remote Setback Control
RSC - Remote Setback Control

The RSC multi-speed control system offers 2 speed fan versatility eg. Energy Management for night-time setback. Can be used in conjunction with Vent-Axia ITC, ITC-DS controllers using 5 step auto-transformer speed controllers for speed selection. Uses 24V output from ITC controller. Dimensions: 86mm x 178mm x 100mm (Width x Height x Depth)

Stock Ref. No: 10314230A
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Find a Distributor
Image of Remote Visual Indicator (RVC)
Remote Visual Indicator (RVC)
Wired in conjunction with either an ITC or ITC-DS controller the RVC can be located up to 100m away using low cost ELV wiring. The compact, single gang RVC ELV (Extra Low Voltage) remote visual controller indicates status of Fan 1 and Fan 2 with status/warning lights. Push button allows Fan 1 and Fan 2 with standby (Off) to be selected.
Stock Ref. No: 10314220
Price £171.09 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Find a Distributor

 

Raadpleeg de tab Downloads voor technische informatie

 

 

ESTIMATED RUNNING COSTS

Calculate estimated running costs for this product using the tool below.
For average costs*, leave the default values in place or enter your own figures in the boxes to recalculate.
Where a product has multi speeds, a typical installation has been used for the below calculations. *Running cost does not include the use of the heater on the heater model


pence
(Your current electricity cost in pence per hour. This will be listed on your electric bill)
hours
(The average number of hours per day fan to run in Trickle mode)
hours
(The average number of hours per day fan to run in Boost mode)

Based on the inputted figures, estimated running costs would be:

Overview

The TDF range are twin backward curved centrifugal impellors (Run & Standby) designed for induct installations.

Casings
Robustly constructed from galvanised sheet steel, fitted with proprietry flanges at each end in accordance with DW142.

Impellers
Aerodynamically designed backward curved constructed from aluminium or steel plate depending on size and rotational speed.

The rotor of the external rotor motor forms the hub of the impeller. Rotors and impellers are factory matched and statically and dynamically balanced on precision machines according to VDI2060 quality class Q6.3.

Motors
Maintenance free external rotor motors with generously dimensioned sealed for life ball bearings encapsulating a high temperature lubricant. The bearings allow for the fan to be mounted at any angle.

Insulation is Class B with the enclosure IP44 according to DIN 40050. The electrical design corresponds to VDE 0530/12.84. The motors are suitable for operation in atmosphere up to 95% RH and ambients up to 40°C.

Motors are wound to suit either 240V 50HZ 1PH or 415V 50HZ 3PH electrical supply. All motors are fitted with Hot Spot protection by means of a thermal contact switch incorporated in the motor windings to prevent motor damage due to overloading. As the motors have a special torque-speed characteristic they are ideally suitable for speed control by voltage reduction.

Performance
Performance figures given have been tested using installation Type ‘D’ in accordance with BS848 Part 1 1980 and BS848 Part 2 1985. The aerodynamic performance data being to tolerance Class ‘C’ as recommended by BSI C.A.M.E Scheme, Certification No CM005.

Sound Levels
Sound Levels are measured in a reverberent chamber in accordance with BS848 Part 2. Sound level measurements are taken with the fan operating at 20% of its maxium pressure development.

Published dBA figures are sound pressure levels measured at a distance of 3m with spherical sound level propagation. It is included for comparative purposes only and the real sound level experienced will depend on the acoustic characteristics of the area being served.

Quality Assurance
Design and manufacture is in accordance with Quality Assured to BS EN ISO9001

Technical

DIMENSIONS:

Unit A B C D E F G H J K L N KG
TDF220 375 330 570 115 400 355 25 9 40 150 115 110 24
TDF250 375 330 570 115 400 355 25 9 40 150 115 110 26
TDF280 425 540 780 190 450 565 25 9 40 150 115 175 40
TDF320 500 655 900 230 525 680 25 9 50 150 130 220 65
TDF380 550 745 1015 260 585 780 35 11 50 160 130 240 75
TDF420 625 830 1130 295 600 865 35 11 50 230 230 220 103
TDF480 700 925 1250 325 735 960 35 11 65 230 230 300 112
TDF520 775 1055 1385 355 810 1090 35 11 50 230 230 350 145
TDF600 850 1200 1530 400 885 1235 35 11 55 230 230 400 180
TDF700 950 1280 1675 430 985 1295 35 11 55 230 230 450 203

Accessories

Image of Trackmaster Twin Fan Controller (ITC)
Trackmaster Twin Fan Controller (ITC)

 

Please click here for the latest product alternative

The ITC model provides automatic changeover on fan failure as well as enabling a manual selection of either fan for duty sharing or test purposes. (BMS compatible via volt free contacts). This controller must have a permanent live supply. Any On/Off switching must be via the sensor connections S1 and SG terminals.

Stock Ref. No: 10314200
This Model no longer available
Image of Trackmaster Twin Fan Controller (ITC-DS)
Trackmaster Twin Fan Controller (ITC-DS)

The ITC-DS model (Duty sharing). Incorporates a timing mechanism which operates alternate fans on 12 or 24 hour intervals, thus ensuring the extended life of the fan bearings. The controller also provides automatic changeover on fan failure along with the facility for manual selection of either fan. (BMS compatible via volt free contacts). This controller must have a permanent live supply. Any On/Off switching must be via the sensor connections S1 and SG terminals

Stock Ref. No: 10314210
Price £600.11 (excl VAT)
Image of RSC - Remote Setback Control
RSC - Remote Setback Control

The RSC multi-speed control system offers 2 speed fan versatility eg. Energy Management for night-time setback. Can be used in conjunction with Vent-Axia ITC, ITC-DS controllers using 5 step auto-transformer speed controllers for speed selection. Uses 24V output from ITC controller. Dimensions: 86mm x 178mm x 100mm (Width x Height x Depth)

Stock Ref. No: 10314230A
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Find a Distributor
Image of Remote Visual Indicator (RVC)
Remote Visual Indicator (RVC)
Wired in conjunction with either an ITC or ITC-DS controller the RVC can be located up to 100m away using low cost ELV wiring. The compact, single gang RVC ELV (Extra Low Voltage) remote visual controller indicates status of Fan 1 and Fan 2 with status/warning lights. Push button allows Fan 1 and Fan 2 with standby (Off) to be selected.
Stock Ref. No: 10314220
Price £171.09 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Find a Distributor

Downloads

Related Products

Useful links