Sentinel Kinetic Cooker Hood
Sentinel Kinetic Cooker Hood

Lo-Carbon Sentinel Kinetic Cooker Hood

• Acoustic Top Box option for reduced in-duct noise
• Recognised in SAP PCDB
• Includes Cooker Hood Canopy
• Horizontal duct option for space-saving installations
• Fits within a 600mm wide aperture (300mm deep)
• Integrated digital controller for simple and accurate commissioning
• Plug and play controls; Humidistat
• BMS connectivity
• LS inputs (Light Switch)
• Volt-free inputs
• Self diagnosis for simplified fault finding
• Adjustable delay On/delay Off timer

Select a product

Easy Installation
Ducting can be attached to the unit horizontally, vertically or both. Minimum internal depth of kitchen cupboard: 300mm.

Horizontal and Vertical Spigots: The combination of spigot options allows installation in confined locations. If vertical and horizontal connection are required on the same outlet/inlet, additional spigots can be supplied.

The condensate connection can be taken through the rear of the unit or through the side of the unit into an adjacent cupboard prior to connection into pre-installed domestic waste water system.

Cooker Hood Unit
The Sentinel Kinetic Cooker Hood is designed to fit in a 600mm wide aperture above a hob. The telescopic hood incorporates two flat removable metal grease filters, low energy light bulbs and is available with a White or Brushed Aluminium front trim. The hood contains an integral fire damper in accordance with BRE Digest 398 and is connected to the heat recovery unit by a galvanised steel duct with access for cleaning. When the hood is opened, the heat recovery unit goes to boost speed and the summer bypass automatically opens to prevent cooking by-products entering the heat recovery cell. As an additional safety feature, the duct also contains a thermal cut-out fuse which turns off the MVHR unit in the event of excessive temperature in the airway. Cooker Hood units cannot be handed on-site and must be
purchased as left hand (L) or right hand (R) models.

SELV Models
SELV cooker hoods allow the distance between the hood and an electric hob to be reduced from 650mm to 550mm.

Integral Humidity Sensor
The integral humidity (models with H suffix) sensor increases speed in proportion to relative humidity levels, saving energy and reducing noise. The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room. The night time relative humidity setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature.

 
Image of Lo-Carbon Sentinel Kinetic CWH L
Lo-Carbon Sentinel Kinetic CWH L
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a White Cooker Hood. This model is supplied left handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446756
Price £3173.27 (excl VAT)
Image of Lo-Carbon Sentinel Kinetic CSH L
Lo-Carbon Sentinel Kinetic CSH L
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a Brushed Aluminium Cooker Hood. This model is supplied left handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446757
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH R
Lo-Carbon Sentinel Kinetic CWH R
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a White Cooker Hood. This model is supplied right handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446758
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH R
Lo-Carbon Sentinel Kinetic CSH R
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a Brush Aluminium Cooker Hood. This model is supplied right handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446759
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH L SELV
Lo-Carbon Sentinel Kinetic CWH L SELV
Stock Ref. No: 477003
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH L SELV
Lo-Carbon Sentinel Kinetic CSH L SELV
Stock Ref. No: 477004
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH R SELV
Lo-Carbon Sentinel Kinetic CWH R SELV
Stock Ref. No: 477005
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH R SELV
Lo-Carbon Sentinel Kinetic CSH R SELV
Stock Ref. No: 477006
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Opto-coupler for volt-free bms connection
Stock Ref. No: 447340
Price £65.51 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Stock Ref. No: 442356
Price £41.95 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter

ISO ePM10 50% (M5) Filter 1 Pack. Formally known as M5, this filter will remove smaller particles, including pollen. 

Replacement filter comprising one supply filter for the Kinetic B, BH, E, V and Cooker Hood units. Pack contains one M5 pollen filter. 

Stock Ref. No: 444199
Price £45.88 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Sentinel Kinetic Wired Remote Controller
Sentinel Kinetic Wired Remote Controller
The Kinetic Wired Remote Controller duplicates all the functions of the on-board controller allowing the unit to be commissioned, controlled and monitored remotely. The controller is supplied with 15 metres of four core cable fitted with an RJ11 plug for fitting to the Kinetic control pcb.
Stock Ref. No: 443283
Price £101.12 (excl VAT)
Image of Wireless enable kit
Wireless enable kit

The Wireless enable kit allows the Kinetic to be set to boost or purge from a remote wireless switch. One switch is supplied with the kit. Up to three additional switches may be linked to the wireless receiver.

Stock Ref. No: 441865
Price £151.68 (excl VAT)
This Model no longer available
Image of Wireless Transmitter Controller
Wireless Transmitter Controller

IMPORTANT – This wireless controller is not compatible with any new Sentinel Multivent Ranges (white units). It is only compatible with these Sentinel Multivent part numbers; 445655, 445655A & 407849.

Stock Ref. No: 437827
Price £93.83 (excl VAT)
This Model no longer available
Image of Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Stock Ref. No: 442356
Price £41.95 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter

ISO ePM10 50% (M5) Filter 1 Pack. Formally known as M5, this filter will remove smaller particles, including pollen. 

Replacement filter comprising one supply filter for the Kinetic B, BH, E, V and Cooker Hood units. Pack contains one M5 pollen filter. 

Stock Ref. No: 444199
Price £45.88 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Sentinel Kinetic Cooker Hood/HR205 grease 2x filters
Sentinel Kinetic Cooker Hood/HR205 grease 2x filters

Replacement filter set comprising 2 filters for the Kinetic Cooker Hoods and HR205.

Stock Ref. No: 372774
Price £143.10 (excl VAT)
Image of LED Indicator
LED Indicator
Compatible with the Sentinel Kinetic range, the LED Indicator illuminates when the MVHR unit requires a filter check or if the unit has a fault. Supplied with 15 metres of cable. 85 x 85 x 10mm (H x W x D)
Stock Ref. No: 448356
Price £56.65 (excl VAT)
Opto-coupler for volt-free bms connection
Stock Ref. No: 447340
Price £65.51 (excl VAT)
Acoustic Purge Fan
Stock Ref. No: 477988
Price £960.21 (excl VAT)
Acoustic Purge Fan XL
Stock Ref. No: 479829
Price £1440.11 (excl VAT)

 

Raadpleeg de tab Downloads voor technische informatie

 

 

ESTIMATED RUNNING COSTS

Calculate estimated running costs for this product using the tool below.
For average costs*, leave the default values in place or enter your own figures in the boxes to recalculate.
Where a product has multi speeds, a typical installation has been used for the below calculations. *Running cost does not include the use of the heater on the heater model


pence
(Your current electricity cost in pence per hour. This will be listed on your electric bill)
hours
(The average number of hours per day fan to run in Trickle mode)
hours
(The average number of hours per day fan to run in Boost mode)

Based on the inputted figures, estimated running costs would be:

Overview

Easy Installation
Ducting can be attached to the unit horizontally, vertically or both. Minimum internal depth of kitchen cupboard: 300mm.

Horizontal and Vertical Spigots: The combination of spigot options allows installation in confined locations. If vertical and horizontal connection are required on the same outlet/inlet, additional spigots can be supplied.

The condensate connection can be taken through the rear of the unit or through the side of the unit into an adjacent cupboard prior to connection into pre-installed domestic waste water system.

Cooker Hood Unit
The Sentinel Kinetic Cooker Hood is designed to fit in a 600mm wide aperture above a hob. The telescopic hood incorporates two flat removable metal grease filters, low energy light bulbs and is available with a White or Brushed Aluminium front trim. The hood contains an integral fire damper in accordance with BRE Digest 398 and is connected to the heat recovery unit by a galvanised steel duct with access for cleaning. When the hood is opened, the heat recovery unit goes to boost speed and the summer bypass automatically opens to prevent cooking by-products entering the heat recovery cell. As an additional safety feature, the duct also contains a thermal cut-out fuse which turns off the MVHR unit in the event of excessive temperature in the airway. Cooker Hood units cannot be handed on-site and must be
purchased as left hand (L) or right hand (R) models.

SELV Models
SELV cooker hoods allow the distance between the hood and an electric hob to be reduced from 650mm to 550mm.

Integral Humidity Sensor
The integral humidity (models with H suffix) sensor increases speed in proportion to relative humidity levels, saving energy and reducing noise. The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room. The night time relative humidity setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature.

Technical

 

Models

Image of Lo-Carbon Sentinel Kinetic CWH L
Lo-Carbon Sentinel Kinetic CWH L
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a White Cooker Hood. This model is supplied left handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446756
Price £3173.27 (excl VAT)
Image of Lo-Carbon Sentinel Kinetic CSH L
Lo-Carbon Sentinel Kinetic CSH L
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a Brushed Aluminium Cooker Hood. This model is supplied left handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446757
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH R
Lo-Carbon Sentinel Kinetic CWH R
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a White Cooker Hood. This model is supplied right handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446758
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH R
Lo-Carbon Sentinel Kinetic CSH R
Compact and recognised in SAP Appendix Q, the Lo-Carbon Sentinel Kinetic CWH L is a highly efficient mechanical ventilation (with heat recovery) unit supplied with a Brush Aluminium Cooker Hood. This model is supplied right handed. Please note that this unit cannot be handed on-site.
Stock Ref. No: 446759
Price £3173.27 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH L SELV
Lo-Carbon Sentinel Kinetic CWH L SELV
Stock Ref. No: 477003
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH L SELV
Lo-Carbon Sentinel Kinetic CSH L SELV
Stock Ref. No: 477004
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CWH R SELV
Lo-Carbon Sentinel Kinetic CWH R SELV
Stock Ref. No: 477005
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Lo-Carbon Sentinel Kinetic CSH R SELV
Lo-Carbon Sentinel Kinetic CSH R SELV
Stock Ref. No: 477006
Price £3171.95 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Opto-coupler for volt-free bms connection
Stock Ref. No: 447340
Price £65.51 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Stock Ref. No: 442356
Price £41.95 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter

ISO ePM10 50% (M5) Filter 1 Pack. Formally known as M5, this filter will remove smaller particles, including pollen. 

Replacement filter comprising one supply filter for the Kinetic B, BH, E, V and Cooker Hood units. Pack contains one M5 pollen filter. 

Stock Ref. No: 444199
Price £45.88 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)

Accessories

Image of Sentinel Kinetic Wired Remote Controller
Sentinel Kinetic Wired Remote Controller
The Kinetic Wired Remote Controller duplicates all the functions of the on-board controller allowing the unit to be commissioned, controlled and monitored remotely. The controller is supplied with 15 metres of four core cable fitted with an RJ11 plug for fitting to the Kinetic control pcb.
Stock Ref. No: 443283
Price £101.12 (excl VAT)
Image of Wireless enable kit
Wireless enable kit

The Wireless enable kit allows the Kinetic to be set to boost or purge from a remote wireless switch. One switch is supplied with the kit. Up to three additional switches may be linked to the wireless receiver.

Stock Ref. No: 441865
Price £151.68 (excl VAT)
This Model no longer available
Image of Wireless Transmitter Controller
Wireless Transmitter Controller

IMPORTANT – This wireless controller is not compatible with any new Sentinel Multivent Ranges (white units). It is only compatible with these Sentinel Multivent part numbers; 445655, 445655A & 407849.

Stock Ref. No: 437827
Price £93.83 (excl VAT)
This Model no longer available
Image of Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO 45% Coarse (G3) 2x Filter

ISO 45% Coarse (G3) (2 pack). Formally known as G3, this filter will provide the minimum required filtration.

Replacement filter set comprising 2 filters for the Kinetic B, BH, E, V and Cooker Hood units. Installation instructions included.

Stock Ref. No: 442356
Price £41.95 (excl VAT)
Image of Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter
Sentinel Kinetic B/BH/Cooker Hood ISO ePM10 50% Pollen (M5) 1x Filter

ISO ePM10 50% (M5) Filter 1 Pack. Formally known as M5, this filter will remove smaller particles, including pollen. 

Replacement filter comprising one supply filter for the Kinetic B, BH, E, V and Cooker Hood units. Pack contains one M5 pollen filter. 

Stock Ref. No: 444199
Price £45.88 (excl VAT)
(Please call 0344 856 0590 0344 856 0590 for further availability information)
Image of Sentinel Kinetic Cooker Hood/HR205 grease 2x filters
Sentinel Kinetic Cooker Hood/HR205 grease 2x filters

Replacement filter set comprising 2 filters for the Kinetic Cooker Hoods and HR205.

Stock Ref. No: 372774
Price £143.10 (excl VAT)
Image of LED Indicator
LED Indicator
Compatible with the Sentinel Kinetic range, the LED Indicator illuminates when the MVHR unit requires a filter check or if the unit has a fault. Supplied with 15 metres of cable. 85 x 85 x 10mm (H x W x D)
Stock Ref. No: 448356
Price £56.65 (excl VAT)
Opto-coupler for volt-free bms connection
Stock Ref. No: 447340
Price £65.51 (excl VAT)
Acoustic Purge Fan
Stock Ref. No: 477988
Price £960.21 (excl VAT)
Acoustic Purge Fan XL
Stock Ref. No: 479829
Price £1440.11 (excl VAT)

Downloads